Can I Install A Bathtub Myself?
Can I Install A Bathtub Myself?
Blog Article
What're your concepts on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround?
:max_bytes(150000):strip_icc()/adhesive-type-tub-and-shower-surround-2718959-hero-22d394dc48de474a988eeaad88e9d7b0.jpg)
Setting up a bathtub isn't exactly brain surgery, however it does require solid plumbing, woodworking, and also often, tiling skills. Replacing an old bath tub with a brand-new one is likewise a moderately hard task. If the old tub is readily accessible, the job can move speedily; if you need to open up a wall to get rid of the old bathtub and position the brand-new tub, the task is a lot harder. In either situation, the project is within a residence handyman's skills, although you will require a helper to move out the old bathtub as well as embeded in the brand-new one. Ensure you have actually certified yourself for the work as well as are comfortable trying it. Rather than working with a specialist to take over a halfway-completed task, it is much better to consider utilizing one before you start. Opportunities are you may require an expert plumber to make tube connections.
This post will aid you install a brand-new bathtub in your washroom if you have currently purchased a brand-new tub and also don't require to change the setup of your previous supply of water pipelines.
Your tools as well as material list should make up the following:
Removing Old Touches
If you need to replace old faucets with new ones as a part of your setup, then the first thing you should do is detach the water. After doing so, turn on the faucets to drain pipes any water continuing to be in the system. The process of eliminating the existing faucets can be quite troublesome as a result of the restricted gain access to that is commonly the case.
Utilize a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that attaches the supply pipes to the taps. Have a fabric all set for the remaining water that will come from the pipes. When the supply pipelines have actually been gotten rid of, make use of the very same device to loosen the nut that holds the taps onto the bath/basin. You will need to stop the single taps from turning during this process. When the taps have been eliminated, the holes in the bath/basin will have to be cleaned up of any type of old securing substance.
Before carrying on to fit the brand-new faucets, compare the pipe connections on the old taps to the new taps. If the old taps are longer than the new taps, then a shank adapter is required for the new faucets to fit.
Suitable New Touches
If the tails of the brand-new faucets are plastic, after that you will certainly need a plastic port to prevent damage to the thread. One end of the connector fits on the plastic tail of the faucet and also the various other end gives a link to the existing supply pipes.
If you need to fit a monobloc, then you will call for lowering couplers, which attaches the 10mm pipeline of the monobloc to the conventional 15mm supply pipe.
Next, position the faucet in the placing opening in the bath/basin guaranteeing that the washers are in area in between the tap and the sink. Safeguard the faucet in place with the producer provided backnut. As soon as the faucet is safely in place, the supply pipelines can be attached to the tails of the taps. The taps can either be attached by utilizing corrugated copper piping or with typical tap adapters. The previous type should be attached to the faucet ends initially, tightening up only by hand. The supply pipes can later on be linked to the other end. Tighten up both ends with a spanner after both ends have been attached.
Setting up the Bathtub
Making use of the two wood boards under its feet, place the bath tub in the required placement. The wooden boards are handy in uniformly spreading out the weight of the tub over the location of the boards rather than concentrating all the weight onto four tiny points.
The following goal is to make sure that the bathtub is leveled all round. This can be attained by checking the level and changing the feet on the bath tub until the level reads degree.
To mount taps, fit all-time low of the furthest versatile faucet connector to the proper supply pipe by making a compression sign up with; then do the exact same for the other tap.
Activate the water supply as well as examine all joints and brand-new pipework for leakages and tighten them if needed. Load the bathtub and additionally check the overflow outlet and also the normal outlet for leakages.
Ultimately, fix the bath paneling as defined in the manufacturer's instruction manual. Tiling as well as securing around the bathtub ought to wait up until the bath tub has been used a minimum of when as this will certainly settle it into its final placement.
Planning for the Installation
First of all, the sustaining structure supplied with the bath must be fitted (if called for) according to the supplier's instructions. Next, fit the taps or mixer to the tub. When suitable the faucet block, it is necessary to see to it that if the tap comes with a plastic washer, it is fitted between the bath as well as the faucets. On a plastic bathroom, it is additionally reasonable to fit a sustaining plate under the faucets unit to prevent strain on the bathtub.
Fit the flexible tap ports to the bottom of the two taps utilizing 2 nuts as well as olives (often provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the electrical outlet with the hole in the bathroom. Utilize the nut supplied by the producer to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the flexible overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bathroom. Make certain you utilize every one of the supplied washers.
Connect the trap to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Connect all-time low of the overflow tube in a comparable manner.The bathroom ought to now be ready to be suited its last setting.
Tiling Around the Tub
In the area where the bath fulfills the floor tile, it is needed to seal the joins with a silicone rubber caulking. This is necessary as the installation can relocate enough to crack an inflexible seal, triggering the water to permeate the wall in between the bathroom as well as the tiling, leading to complications with wetness as well as possible leakages to the ceiling below.
You can choose from a selection of coloured sealants to blend in your components as well as fittings. They are marketed in tubes as well as cartridges, as well as are capable of securing voids approximately a width of 3mm (1/8 inch). If you have a bigger space to fill, you can load it with spins of soaked paper or soft rope. Keep in mind to always load the tub with water prior to securing, to allow for the motion experienced when the tub remains in usage. The sealant can fracture rather early if you do not consider this movement prior to sealing.
Alternatively, ceramic coving or quadrant floor tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are also easily readily available on the market. It is advisable to fit the floor tiles utilizing waterproof or water resistant adhesive and also grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
We had been shown that editorial on Tools You Need to Install a New Bathtub from an associate on another web blog. Sharing is caring. Helping people is fun. I praise you for your time. Visit us again soon.
Visit The Following Page
Report this page